🌂 How Tight Should A Serpentine Belt Be

The part number is 90916-02500. The revised specs for tension say to install the new belt, start the engine and let it run for about 20 minutes to allow the belt to stretch a bit then shut it down. Measure the deflection of the belt in the center of the span between the alternator and the crank pulley. Step 2: Open the Hood: Now that you have the belt in hand, it’s time to start installing. The first step is to open the hood of the car. This will give you access to the engine and the belts. Be sure to open the hood before you start so that you don’t have to stop in the middle of the job. So, identify the cause of the dirt and clean the pulley using an appropriate solvent. You can also use soapy water to reduce belt squeaking. Spray the soapy water on the serpentine belt and then wait to hear if the squeaking sound will reduce or stop. If it doesn’t, you should resort to other long-term solutions. 3. Gates K060882 Micro-V Serpentine Drive Belt. The Gates K060882 Micro-V Serpentine Drive Belt is an auto part made in China. It comes in compact package dimensions of 3.556 cm length, 8.382 cm width, and 35.814 cm height, with a weight of 0.52 lbs. This product falls under the category of car serpentine belts. A serpentine belt is a strong rubber belt that controls most of the accessories inside the engine system. It should be in a middle range that is highly suitable for your engine system. The tension of the belt depends on the pulleys and connections, and it should not be too loose or too tight. Learn how to check and adjust the tension of the serpentine belt with a generator or an automatic tensioner. Typical service factors for serpentine drives are no less than 2.0, but because of shock loading and relatively tight drive geometry, we choose a slightly more conservative service factor of 2.2. If there is a grinding sound or friction, the bearings are worn or damaged and should be replaced. Mark the face or edge of the pulley with chalk or a grease pencil and reattach and tighten the belt. Start the engine and drop it into a slow idle. If the mark and the noise seem to align, you have a damaged bearing. 5. That video is useless, guy just offers up a theory when the real solution is obvious (the belt needs to be tighten). I wouldn't be overly concerned with the belt being to tight. I've changed the serpentine belt on a Toyota 1.8L 1ZZ engine which is the big sister 1.5L 1NZ in the Yaris. Belt Tension Calculator. Proper belt tension ensures optimum performance of a vehicle's accessory belt drive system. Select from the dropdown options below to find the appropriate belt tension for your belt. ABOUT US. ford: foucs 2.0 dohc..pry..tight..autozone for the belt ok any tips on installing a serpintine belt on a 03 ford foucs 2.0 dohc. have tried to pry it on and use brut force w/ no luck belt is tight have about one inch to go till it gets on but cant strech i … Not pretty. Loosen that pivot bolt and THEN try to adjust the tensioning rod. If there's already tension, then your tensioner is fine. You've got a pulley going out somewhere. 50% its the tensioner pulley. 49% the idler pullet (top passenger side of motor). 1% any other pulley. 1999 C43 AMG 744-Silver - Mine. When installing the belt, make sure the belt is centered on the pulleys. Install the splash shield, wheel and lug nuts. Lower the vehicle and tighten the lug nuts to the proper torque: Wheel lug nuts 80 ft-lbs; Automatic drive belt tensioner replacement (1.8L, 2.0L and 2.4L engines) Remove the drive belt (see Steps 15 and 16 above). C4 Serpentine Belt Replacement. Time: 30 to 60 minutes. Tools: ½” breaker bar. Torque: Belt tensioner to engine block – 30 lb./ft. Talent: (3) Applicable Years: 1984 to 1996. Tab: Under $50.00. Tip: Consider purchasing the tool designed to release the belt tensioner. This works very nicely and is cheap. A serpentine belt is a vital part of a vehicle’s engine, and it needs to be tight enough to function properly. If the belt is too loose, it can slip off the pulleys and cause the engine to overheat or stall. If the belt is too tight, it can wear out prematurely or break. The ideal tension for a serp SERPENTINE BELT REMOVAL REPLACEMENT 2.4 MULTIAIR ENGINE DODGE DART CHRYSLER 200 JEEP FIATIf you need to remove or replace the serpentine belt on a 2.4 Multia .

how tight should a serpentine belt be